displaying posts 1 to 8 of 8

Author Subject: Braided Hoses - Black Diamond?
ash j

Regular

Location: Fareham

Registered: 02 Mar 2011

Posts: 415

Status: Offline

Post #1
Looking for a set of braided hoses for my 306.

Have PM'd swampy on this forum and he has got back to me with a very reasonable price for a kit in carbon look.

However, I am looking for a set with stainless fittings ideally, as opposed to the zinc ones.

Goodridge or HEL are the obvious choice, but they are certainly not cheap, or at least seem expensive compared to the price from swampy.

Then I noticed that Black Diamond do a set of braided hoses for a good price, but they are only listed for the XSi.

Will they still fit GTi-6 calipers?

And would everybody else suggest going for stainless fittings too?

Cheers
Posted 6th Jul 2011 at 00:30
prism7guy

Seasoned Pro

Location: DoncastAAAAARGH

Registered: 13 Jan 2008

Posts: 4,640

Status: Offline

Post #2
I have stainless fittings on the kits on both my gti6's, both supplied by swampy. Wink

________________________________________

Goldie the track car.
Posted 6th Jul 2011 at 00:46
mr swampy s16

**BAD SELLER**

Location: out and about

Registered: 22 Oct 2003

Posts: 10,550

Status: Offline

Post #3
Blackdiamond are made by exact who supply my lines.
Posted 6th Jul 2011 at 00:51
jeffers Forum Admin

Location: Leeds

Registered: 14 Dec 2003

Posts: 3,702

Status: Offline

Post #4
I have HEL lines on my track car, top quality and iirc they cost £50 delivered, but iirc they have 10 percent online discount at the min...

________________________________________

Team Running Engine again!
Team Negative Camber!
My Budget track engine build thread!
Now appearing at a Trackday near you!!Hyper Hyper
Posted 6th Jul 2011 at 01:17
miles

Seasoned Pro

Location: Ringwood

Registered: 28 Dec 2002

Posts: 3,433

Status: Offline

Post #5
Give them a call and check then at least you have some ammo if they are supplied wrong.
Again I've had some HEL ones supplied for a 1.6 205 and 1 rear was wrong, just a female fitting instead of a male fitting, But even motor factors get this wrong
Worth noting the rears are different depending on the year of the car as not all have the Valve on the back

________________________________________

306 Rallye Sptint/Race Car, 205 CTI 1.9 8v to name a few

Road, Track and Race/Rally car preparation to your personal requirements,
Full Workshop & Diagnostic Facilities
New and Second parts, from Plugs to Turbo's
We now also carry out Routine Servicing
www.pugracing.com

& FB Page, https://www.facebook.com/PugRacing

Ebay; http://stores.ebay.co.uk/Pug-Racing-Shop

2012/2013/2014/2019 Class Winners at Gurston Down Speed Hillclimb & Joint overall, Class record too along the way,
Posted 6th Jul 2011 at 04:28
jeffers Forum Admin

Location: Leeds

Registered: 14 Dec 2003

Posts: 3,702

Status: Offline

Post #6
I had exactly this problem a while back when I refurbed my beam, when I received my hoses the rear ones where both the same size and consequently one was too short, one e mail to the hel supplier and a longer one was sent out no questions asked! Big grin

________________________________________

Team Running Engine again!
Team Negative Camber!
My Budget track engine build thread!
Now appearing at a Trackday near you!!Hyper Hyper
Posted 6th Jul 2011 at 04:31
mjstones

Seasoned Pro

Location: straight outta compton

Registered: 16 Oct 2007

Posts: 1,233

Status: Offline

Post #7
i've got a set of swampy, seem to be all working nice. braking seems improved. only 1 slight issue was that 1 was a bit too long, fixed with a tie wrap to a bit in the wheel arch, but that was the fault of a lazy garage guy rather than the hose. but so far i'm impressed with the swampy ones. bearing in mind new pads were fitted at the same time (the garage neglected to tell me this and i didn't notice til i got home) and the brakes still felt better than before.

________________________________________

Never underestimate the power of De-Nile.

Friday afternoon car, built in France.... Ninja

306gti6.com Stickers available, pm me for details. or email MjStones83@hotmail.com

Sticker Thread with pics


Posted 6th Jul 2011 at 09:37
chas

Seasoned Pro

Location: Warwickshire

Registered: 31 Oct 2007

Posts: 1,468

Status: Offline

Post #8
I have some of Miles' hoses on my 205. Hoses were spot on, and a doddle to fit (the unions on the hoses (his anyway) make that particularly handy and easy to install).

Unlike the Exact items, they are also have swaged fittings.

________________________________________

Ex Owner of 2000 Phase 3 306 GTi 6 China Blue - You shall be missed

1974 Triumph Stag
1989 Peugeot 205 GTi 1.6
2003 Alfa Romeo 147 JTD Lusso
2005 Mondeo Ghia X 3.0 Estate LPG
Posted 6th Jul 2011 at 12:40

All times are GMT. The time is now 12:57

The Peugeot GTi-6 & Rallye Owners Club - ©2024 all rights reserved.

Please Note: The views and opinions found herein are those of individuals, and not of The Peugeot 306 GTi-6 & Rallye Owners Club or any individuals involved.
No responsibility is taken or assumed for any comments or statements made on, or in relation to, this website. Please see our updated privacy policy.