Author	Subject: Gasket doesn't fit??
l8un08 Junior User Location: cardiff Registered: 30 May 2011 Posts: 61 Status: Offline	Post #1 Pug 306 1.8! R reg! Iv had all my head skimmed,crack tested etc! And the gasket doesn't fit?? Iv got another gasket and that doesn't fit either even though they were both for pug 306's! No engine number apparently may have been n import? What to do now? ________________________________________ bloooobirds
Posted 9th Jun 2011 at 21:42 Profile

ryangti6 Seasoned Pro Location: Pontypool Registered: 01 Sep 2006 Posts: 1,839 Status: Offline	Post #2 In what way does it not fit? ________________________________________ Ryan
Posted 9th Jun 2011 at 21:48 Profile

l8un08 Junior User Location: cardiff Registered: 30 May 2011 Posts: 61 Status: Offline	Post #3 ryangti6 wrote: In what way does it not fit? I'm not sure mate as I'm not doing it a mate is! The original blown gasket is now at a motorfactors and their trying to match one up! Fingers crossed ________________________________________ bloooobirds
Posted 9th Jun 2011 at 21:49 Profile

mark.evs Senior User Location: Near Bridgend Registered: 21 Dec 2010 Posts: 527 Status: Offline	Post #4 what factors are u using? remind me not to go there. ________________________________________ My GTi6 track project White Rallye project
Posted 9th Jun 2011 at 21:56 Profile

owain Seasoned Pro Location: Essex Registered: 20 May 2009 Posts: 9,185 Status: Offline	Post #5 mark.evs wrote: what factors are u using? remind me not to go there. Well said Are you sure you're not confusing a head gasket with a selection of lego bricks? Because they won't fit. ________________________________________ Membership expiring soon, get in contact on our new little forum project.
Posted 9th Jun 2011 at 21:57 Profile

l8un08 Junior User Location: cardiff Registered: 30 May 2011 Posts: 61 Status: Offline	Post #6 Doh!!! Ye I had Lego bricks! ________________________________________ bloooobirds
Posted 9th Jun 2011 at 21:59 Profile

davedgti6 Seasoned Pro Location: whiston, prescot Registered: 28 May 2006 Posts: 1,651 Status: Offline	Post #7 Better to use genuine pug head gasket rather than a pattern part, motor factors gaskets are usually poo ________________________________________ Team Supercharged Gti-6™
Posted 9th Jun 2011 at 22:03 Profile

ablister Senior User Location: fife Registered: 30 Oct 2005 Posts: 522 Status: Offline

Post #8 davedgti6 wrote: Better to use genuine pug head gasket rather than a pattern part, motor factors gaskets are usually poo motor factor stuff is ok if you know what to ask for. Peugeot don't make gaskets, they just get companies (normally 'corteco') to make them then they are put in nice peugeot packaging. So you can get 'genuine' parts from motor factors for (usually!) cheaper... ________________________________________ 306 rallye, Richard Longman engine rc10gt

Posted 11th Jun 2011 at 19:52 Profile

The Peugeot GTi-6 & Rallye Owners Club - ©2026 all rights reserved.

Please Note: The views and opinions found herein are those of individuals, and not of The Peugeot 306 GTi-6 & Rallye Owners Club or any individuals involved.
No responsibility is taken or assumed for any comments or statements made on, or in relation to, this website. Please see our updated privacy policy. (NEW HOST)